Husqvarna 701 Enduro 2017 Repair Manual page 263

26 TECHNICAL DATA
261
Screw plug, crankshaft clamp M8 15 Nm (11.1 Ibf ft)
Loctite® 243™ Stud, exhaust flange 10 Nm (7.4 Ibf ft) M8
Cylinder head screw M10 Tightening sequence:
Tighten diagonally, begin­
ning with the rear screw on
the timing chain shaft.
Step 1
15 Nm (11.1 Ibf ft)
Step 2
30 Nm (22.1 Ibf ft)
Step 3
45 Nm (33.2 Ibf ft)
Step 4
60 Nm (44.3 Ibf ft)
Lubricated with engine oil
Oil line for oil pressure sensor 10 Nm (7.4 Ibf ft) M10x1
Oil pressure sensor 10 Nm (7.4 Ibf ft) M10x1
Plug, drain hole of water pump 15 Nm (11.1 Ibf ft) M10x1
Loctite® 243™ Screw plug, oil channel M10x1 15 Nm (11.1 Ibf ft)
Screw plug, oil channel, for oil radiator M10x1 15 Nm (11.1 Ibf ft)
Screw, unlocking of timing chain ten­
sioner
10 Nm (7.4 Ibf ft) M10x1
Spark plug outside 11 Nm (8.1 Ibf ft) M10x1
Spark plug inside
18 Nm (13.3 Ibf ft) M12x1.25
Coolant temperature sensor on cylin­
der head
M12x1.5 12 Nm (8.9 Ibf ft)
Oil drain plug with magnet M12x1.5 20 Nm (14.8 Ibf ft)
Oil pressure regulator valve plug M12x1.5 20 Nm (14.8 Ibf ft)
Loctite® 243™ Screw plug, oil channel 15 Nm (11.1 Ibf ft) M14x1.5
Loctite® 243™ 25 Nm (18.4 Ibf ft) Engine case stud M16x1.5
Rotor nut M18x1.5 100 Nm (73.8 Ibf ft)
Loctite® 243™ Nut, engine sprocket M20x1.5 80 Nm (59 Ibf ft)
Loctite® 243™ 100 Nm (73.8 Ibf ft) Nut, inner clutch hub M20x1.5
Loctite® 243™ 90 Nm (66.4 Ibf ft) Nut, primary gear M20LHx1.5
15 Nm (11.1 Ibf ft) Plug, oil screen M20x1.5
Plug, timing chain tensioner M20x1.5 25 Nm (18.4 Ibf ft)
Plug, oil thermostat M24x1.5 15 Nm (11.1 Ibf ft)
Screw in alternator cover 8 Nm (5.9 Ibf ft) M24x1.5
Capacities
26.4
Engine oil 26.4.1
Engine oil (SAE 10W/50) (m p. 316) 1.70 I (1.8 qt.) Engine oil
26.4.2 Coolant
Coolant (81 p. 316) Coolant 1.20 I (1.27 qt.)
26.4.3 Fuel
Super unleaded (ROZ 95/RON 95/PON 91) (^ p. 317) Total fuel tank capacity,
approx.
13 I (3.4 US gal)
Fuel reserve, approx. 2.5 I (2.6 qt.)