Mitsubishi Electric Q26UD(E)HCPU User Manual page 486

(11)Built-in Ethernet port QCPU, built-in Ethernet port LCPU, and built-in Ethernet
function
Number Name
MELSOFT
connection
extended setting OFF: Invalid
SM1258
network number, ON: Valid
station number
enable flag
OFF: No time setting
Time setting
SM1270 function (SNTP
ON: Time setting
client) execution
Remote
password OFF: Normal
SM1273
mismatch count ON: Clear
clear
IP address
OFF  ON:Write request
SM1292 storage area
write request
IP address
OFF: Not completed
SM1293 storage area
ON: Completed
write completion
IP address
OFF: Normal
SM1294 storage area
ON: Errors
write error
IP address
OFF  ON:Clear request
SM1295 storage area
clear request
IP address
OFF: Not completed
SM1296 storage area
ON: Completed
clear completion
IP address
OFF: Normal
SM1297 storage area
ON: Errors
clear error
OFF: Not connected
FTP client
SM1298
connection status
ON: Connected
*1 Built-in Ethernet port QCPU and Built-in Ethernet port LCPU
*2 Built-in Ethernet port QCPU whose serial number (first five digits) is "11082" or later
*3 Built-in Ethernet port LCPU whose serial number (first five digits) is "15102" or later
*4 Built-in Ethernet port LCPU whose serial number (first five digits) is "16112" or later
*5 Modules whose serial number (first five digits) is "17052" or later
484
Meaning
This relay turns on when the network
number and station number of built-in
Ethernet port set in the MELSOFT
connection extended setting. (Only when
the MELSOFT connection extended setting
is set to "Use".)
This relay is turned on to perform the time
function (SNTP
setting function (SNTP client). (Turns on
client) execution
only when "Use" has been set for the time
setting function in the time setting
function (SNTP
parameter.)
client) execution
This relay is turned on to clear the
accumulated number of mismatched
remote password entries (SD979 to
SD999).
The IP address setting stored in SD1292 to
SD1297 are written to the IP address
storage area (flash ROM) of the CPU
module when the END instruction is
executed in the scan where this relay is
turned on.
• This relay turns on when writing to the IP
address storage area (flash ROM) is
completed.
• This relay turns off when the END
instruction is executed in the scan where
SM1292 is turned off.
• This relay turns on when writing to the IP
address storage area (flash ROM) fails.
• This relay turns off when the END
instruction is executed in the scan where
SM1292 is turned off.
The IP address storage area (flash ROM)
is cleared when the END instruction is
executed in the scan where this relay is
turned on.
• This relay turns on when clearing the IP
address storage area (flash ROM) is
completed.
• This relay turns off when the END
instruction is executed in the scan where
SM1295 is turned off.
• This relay turns on when clearing the IP
address storage area (flash ROM) fails.
• This relay turns off when the END
instruction is executed in the scan where
SM1295 is turned off.
This relay turns on when the connection
with the FTP server is established. This
(Disconnected)
relay turns off when the connection with the
FTP server is cut off.
Explanation
(When Set)
S (Initial)
S (Status
change)
S (Status
change)
S (Status
change)
S (Status
change)
S (Status
change,
processing)
Corresponding
Set by Corresponding
ACPU
M9
New
U New
U New
U New
New
New
U New
New
New
New
END
CPU
*5
QnUDV
*1
QnU
*1
LCPU
*1
QnU
*1
LCPU
*2
QnU
*3
LCPU
*2
QnU
*3
LCPU
*2
QnU
*3
LCPU
*2
QnU
*3
LCPU
*2
QnU
*3
LCPU
*2
QnU
*3
LCPU
*4
LCPU