Toshiba GR-200 Series Instruction Manual page 405

Signal name and number
(iii)
Note: The user should note the following descriptions shown in the column "M/O" for
each table:
"O" indicates that the signal is provided for optional use.
"M" indicates that the user should map/set/configure the signal; otherwise, the
"N/A" indicates that the user cannot change the state of the signal.
Table 3.5-1 Mapping points for the reception of control command
Signal Number
540001 700E016D09
540001 700E026D09
540001 700E036D09
...
540001 700E206D09
Signal Number
5A0001 0008001F40
5A0101 3100001F43
Table 3.5-3 PLC Connection point (Input signals from the control hierarchy logic)
Signal Number
540001 800E00ED5A
Table 3.5-4 PLC Monitoring points (Signal "select complete/ failed" for BIO)
Signal Number
540001 8A0E011E76
540001 8A0E021E76
540001 8A0E031E76
...
540001 8A0E201E76
5400018B0E011E7B
5400018B0E021E7B
5400018B0E031E7B
....
5400018B0E201E7B
Table 3.5-5 PLC Monitoring points (Signal "stSeld" for BIO)
Signal Number
540001 000E011D91
540001 000E021D91
540001 000E031D91
540001 000E041D91
...
540001 000E201D91
user may experience an operational failure if the default settings are
used.
Signal Name
GCNT01_CMM_REQ
GCNT02_CMM_REQ
GCNT03_CMM_REQ
...
GCNT32_CMM_REQ
Table 3.5-2 Input signals to condition logic
Signal Name
Traveling OR
SERI_ERR
Signal Name
GCNT00IN_TMP_51
Signal Name
GCNT01_SLD_CSCN
GCNT02_SLD_CSCN
GCNT03_SLD_CSCN
...
GCNT32_SLD_CSCN
GCNT01_SLF_CSCN
GCNT02_SLF_CSCN
GCNT03_SLF_CSCN
...
GCNT32_SLF_CSCN
Signal Name
GCNT01_TMP_01
GCNT02_TMP_01
GCNT03_TMP_01
GCNT04_TMP_01
...
GCNT32_TMP_01
- 386 -
Description
GCNT01 control request(Mapping data)
GCNT02 control request(Mapping data)
GCNT03 control request(Mapping data)
...
GCNT32 control request(Mapping data)
Description
Travelling events are detected.
Serious Error detected
Description
Control hierarchy for GCNT01–32
Description
GCNT01 Selection completed (Mapping)
GCNT02 Selection completed (Mapping)
GCNT03 Selection completed (Mapping)
...
GCNT32 Selection completed (Mapping)
GCNT01 select failed
GCNT02 select failed
GCNT03 select failed
...
GCNT32 select failed
Description
GCNT01 count change selected signal(stSeld) for SAS
GCNT02 count change selected signal(stSeld) for SAS
GCNT03 count change selected signal(stSeld) for SAS
GCNT04 count change selected signal(stSeld) for SAS
...
GCNT32 count change selected signal(stSeld) for SAS
6F2T0200 (0.15)
M/O
M
M
M
M
M/O
N/A
N/A
M/O
M
GRE200 (1,2)