ABB ACS560 Firmware Manual page 208
General purpose drives
Hide thumbs
Also See for ACS560:
- Quick installation and start-up manual (306 pages) ,
- Hardware manual (240 pages) ,
- Quick installation and start-up manual (232 pages)
Table of Contents
Advertisement
208 Parameters
No.
Name/Value
DI6
Timed function 1
Timed function 2
Timed function 3
Supervision 1
Supervision 2
Supervision 3
Other [bit]
20.25
Jogging enable
Not selected
Selected
DI1
DI2
DI3
DI4
DI5
DI6
Timed function 1
Timed function 2
Timed function 3
Supervision 1
Supervision 2
Supervision 3
Other [bit]
20.26
Jogging 1 start
source
Not selected
Selected
Description
Digital input DI6
(10.02 DI delayed
Bit 0 of
34.01 Timed functions status
Bit 1 of
34.01 Timed functions status
Bit 2 of
34.01 Timed functions status
Bit 0 of
32.01 Supervision status
Bit 1 of
32.01 Supervision status
Bit 2 of
32.01 Supervision status
Source selection (see
Terms and abbreviations
Selects the source for a jog enable signal.
(The sources for jogging activation signals are selected by
parameters
20.26 Jogging 1 start source
start
source.)
1 = Jogging is enabled.
0 = Jogging is disabled.
Note: Jogging can be enabled only when no start command
from an external control location is active. On the other hand,
if jogging is already enabled, the drive cannot be started from
an external control location (apart from inching commands
through fieldbus).
See section
Rush control
0
1
Digital input DI1
(10.02 DI delayed
Digital input DI2
(10.02 DI delayed
Digital input DI3
(10.02 DI delayed
Digital input DI4
(10.02 DI delayed
Digital input DI5
(10.02 DI delayed
Digital input DI6
(10.02 DI delayed
Bit 0 of
34.01 Timed functions status
Bit 1 of
34.01 Timed functions status
Bit 2 of
34.01 Timed functions status
Bit 0 of
32.01 Supervision status
Bit 1 of
32.01 Supervision status
Bit 2 of
32.01 Supervision status
Source selection (see
Terms and abbreviations
If enabled by parameter
source for the activation of jogging function 1. (Jogging
function 1 can also be activated through fieldbus regardless
of parameter 20.25.)
1 = Jogging 1 active
Notes:
• If both jogging 1 and 2 are activated, the one that was
activated first has priority.
• This parameter cannot be changed while the drive is
running.
0
1
status, bit 5)
(see page 273)
(see page 273)
(see page 273).
(see page 266)
(see page 266)
(see page 266)
on page 162) -
and
20.27 Jogging 2
(page 73).
status, bit 0)
status, bit 1)
status, bit 2)
status, bit 3)
status, bit 4)
status, bit 5)
(see page 273)
(see page 273)
(see page 273)
(see page 266)
(see page 266)
(see page 266)
on page 162) -
20.25 Jogging
enable, selects the
Def/FbEq16
7
18
19
20
24
25
26
Not selected
0
1
2
3
4
5
6
7
18
19
20
24
25
26
Not selected
0
1
- Quick Links:
- Start-Up, Control with I/O and ID...
Hide quick links:
Advertisement
Table of Contents
