Default Control Connections For The Abb Potentiometer Macro; Terminal Sizes - ABB ACS560 Firmware Manual

114 Control macros


Default control connections for the ABB potentiometer macro

1...10 kohm
Max.
500 ohm
3)
R3...R8
4)

Terminal sizes

• (frames R0...R8): 0.14...1.5 mm
• Tightening torques: 0.5...0.6 N·m (0.4 lbf·ft)
X1 Reference voltage and analog inputs and outputs
1 SCR
2
3 AGND
4 +10V
5
6 AGND
7 AO1
8 AO2
9 AGND
X2, X3 Aux. voltage output and programmable digital inputs
10 +24V
11 DGND
4)
12 DCOM
13
14
15
16
17
18
X6,X7, X8 Relay outputs
19 RO1C
20 RO1A
21 RO1B
22 RO2C
23 RO2A
24 RO2B
25 RO3C
26 RO3A
27 RO3B
X5 Built-in fieldbus
29
30
31 DGND
(Frame R0...R2)
S100 TERM&BIAS
(Frame R3...R8)
S100 TERM
S200 BIAS
Safety torque off
X4
R0...R2 R3...R
33 -
34 SGND
4) 35 OUT1 SGND
7)
36 IN1
4)
37 IN2
X10 24 V AC/DC (frames R6...R8 only)
40 24 V AC/DC- in
41 24 V AC/DC+ in
X11 Redundant auxiliary voltage output (frames R0...R2)
42 +24 V
43 DGND
44 DCOM
2
Signal cable shield (screen)
AI1 Not configured
Analog input circuit, common
10 V DC reference voltage
AI2 Not configured
Analog input circuit, common
Output frequency: 0...20 mA
Motor current: 0...20 mA
Analog output circuit common
Aux. voltage output +24 VDC, max. 250 mA
Aux. voltage output common
Digital input common for all
DI1 Stop (0) / Start (1)
DI2 Forward (0) / reverse (1)
DI3 Reference up
DI4 Reference down
DI5 Constant frequency
DI6 Run enable (if 0, drive stops)
Ready run
B+ Internal Modbus RTU (EIA-485). See
A-
control through the embedded fieldbus interface
(EFB).
Termination resistor and bias resistor switch
Termination resistor switch
Bias resistor switch
OUT1
Safety torque off function. Factory connection.
OUT2
Both circuits must be closed for the drive to start.
See Safe torque off function in the drive
IN1
hardware manual.
IN2
24V AC/DC input, for control unit power supply
when external main power is disconnected.
Aux. voltage output +24 V DC, max. 250 mA
Aux. voltage output common
Digital input common for all
(all terminals)
6)
: see
6)
: see 13.22
5)
: see 20.03
5)
: see 20.03
1) 5)
: see 22.73
1)5)
: see 22.74
5)
:see 28.22
5)
: see
6)
: see 10.24.
250 V AC / 30 V DC
2 A
6)
Running : see 10.27.
250 V AC / 30 V DC
2 A
6)
Fault (-1) : see 10.30.
250 V AC / 30 V DC
2 A
13.12
2)
20.12
Fieldbus
2)