Huawei SmartAX MA5603T Configuration Manual page 538

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
6.
7.
Step 3 Configure the time server.
huawei(config)#ntp-service unicast-server 4.4.4.4 source-interface vlanif 10
huawei(config)#ntp-service unicast-server 4.4.4.5 source-interface vlanif 10
Step 4 Configure the log host.
huawei(config)#loghost add 3.3.3.3 syslog-1
huawei(config)#loghost activate ip 3.3.3.3
huawei(config)#loghost add 3.3.4.3 syslog-2
huawei(config)#loghost activate ip 3.3.4.3
Step 5 Configure the EMU.
This topic uses the fan monitoring as an example to show how to configure the EMU.
In this example, assume that the slave node number is 1. In this case, you need to set the DIP
switch of the node address on the fan monitoring unit as 1.
huawei(config)#emu add 0 h801ESC 0 0
huawei(config)#emu add 1 fan 0 1
Step 6 Configure GIU subtending.
MA5600T-1 is subtended with MA5600T-2 andMA5600T-3. Therefore, the subtending should
be configured.
huawei(config)#vlan 60 to 62 standard
huawei(config)#port vlan 60 to 62 0/19 0-1
It will take several minutes, and console may be timeout, please use command
idle-timeout to set time limit
Are you sure to add standard port(s)? (y/n)[n]:y
huawei(config)#vlan 101 to 102 standard
huawei(config)#port vlan 101 to 102 0/19 0-1
It will take several minutes, and console may be timeout, please use command
idle-timeout to set time limit
Are you sure to add standard port(s)? (y/n)[n]:y
Step 7 Configure the ADSL2+ service.
The MA5600T supports the ADSL2+ service of multiple encapsulation modes, such as IPoA,
PPPoA, IPoE, and PPPoE. This topic uses the PPPoE mode as an example to describe how to
configure the ADSL2+ service. For other encapsulation modes, see
the xDSL Internet Access
1.
Issue 01 (2014-04-30)
huawei(config)#snmp-agent trap enable standard
Set trap destination address.
huawei(config)#snmp-agent target-host trap-hostname huawei address 2.2.2.2
trap-paramsname abc
huawei(config)#snmp-agent target-host trap-hostname huawei123 address 2.2.2.3
trap-paramsname 123
Set trap source address.
huawei(config)#snmp-agent trap source vlanif 10
Service."
Configure the ADSL2+ line profile.
You can configure it based on your requirements.
huawei(config)#adsl line-profile add 10
Start adding profile
Press 'Q' to quit the current configuration and new configuration will be
neglected
> Do you want to name the profile (y/n) [n]:
> Transmission mode:
> 0: Custom
> 1: All (G992.1~5,T1.413,ETSI)
> 2: Full rate(G992.1/3/5,T1.413,ETSI)
> 3: G.DMT (G992.1/3/5)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7 Example: Subtending Networking
"3.1 Example: Configuring
513