Huawei SmartAX MA5603T Configuration Manual page 295

Access module
Hide thumbs Also See for SmartAX MA5603T:
Table of Contents

Advertisement

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
4.
5.
Step 5 In the case of the VDSL access mode, follow this procedure.
In this example, the VDSL normal mode is used as an example.
1.
2.
Issue 01 (2014-04-30)
3 576
20432
4 64
4048
5 2048
67536
6 off
off
---------------------------------------------------------------------------
Total Num : 7
According to service requirement, the user access rate is 2048 kbit/s. The query result shows
that traffic profile 5 meets the requirement.
NOTE
l If no traffic profile in the system meets the service requirement, run the traffic table ip command to
configure a new traffic profile.
l On the MA5600T/MA5603T/MA5608T, the user access rate can be limited by either a traffic profile
or an SHDSL line profile. When both profiles are configured, the user bandwidth adopts the minimum
value in the two profiles. In this example, the traffic profile is used to limit the user access rate.
Run the service-port command to create a service port. The index of the new service virtual
port is 2, the access port is port 0/3/1, traffic profile 5 meets the service requirement, and
the S-VLAN is VLAN 50. The VPI and VCI must be the same as the management VPI and
VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1
and 39. To facilitate the maintenance of the service port, also configure the service port
description.
huawei(config)#service-port 2 vlan 50 shdsl mode atm 0/3/1 vpi 1 vci 39 inbound
traffic-table
index 5 outbound traffic-table index 5
huawei(config)#service-port desc 2 description MA5600T/MA5603T/MA5608THW/
Vlanid:50/shdsl/smart
Set the maximum number of MAC addresses that can be learned by the service port is 16.
This parameter is to limit the maximum number of the MAC addresses that can be learned
by one account, namely the maximum number of the PCs that can access the Internet
through one account.
huawei(config)#mac-address max-mac-count service-port 2 16
Configure a VDSL profile. For details, see Configuring VDSL2 Templates and
Profiles. Assume that the VDSL profile ID is 3, downstream rate is 2048 kbit/s, channel
mode is the interleave mode, maximum downstream interleave delay is 8 ms, maximum
upstream interleave delay is 2 ms, SNR margin is 6 dB, minimum downstream INP is 4,
and minimum upstream INP is 2.
huawei(config)#vdsl line-profile quickadd 3 snr 60 0 300 60 0 300
huawei(config)#vdsl channel-profile quickadd 3 path-mode atm interleaved-delay
8 2 inp 4 2 rate
128 10000 128 10000 2048 2048
huawei(config)#vdsl line-template quickadd 3 line 3 channel1 3 100 100
Activate the VDSL port. The access port is port 0/4/1, and VDSL line template 3 and the
default VDSL alarm template (alarm template 1) are bound to the port.
NOTE
By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.
huawei(config)#interface vdsl 0/4
huawei(config-if-vdsl-0/4)#deactivate 1
huawei(config-if-vdsl-0/4)#activate 1 template-index 3
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1152
40864
2 -
128
8096
4 -
4096
135072
0 -
off
off
0 -
3 Configuring the DSLAM Services
tag-pri
tag-pri
tag-pri
tag-pri
270

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Smartax ma5600tSmartax ma5608t

Table of Contents