Siemens Sinumerik 840D sl Diagnostic Manual page 405

03/2009
- 34 Delay cross-comparison MD36950 $MA_SAFE_MODE_SWITCH_TIME.
- 35 Delay pulse disable Stop B MD36956 $MA_SAFE_PULSE_DISABLE_DELAY.
- 36 Delay pulse disable test stop MD36957 $MA_SAFE_PULSE_DIS_CHECK_TIME
- 37 Delay Stop C -> SBH MD36952 $MA_SAFE_STOP_SWITCH_TIME_C.
- 38 Delay Stop D -> SBH MD36953 $MA_SAFE_STOP_SWITCH_TIME_D.
- 39 Delay Stop E -> SBH MD36954 $MA_SAFE_STOP_SWITCH_TIME_E.
- 40 Stop reaction on SG exceeded MD36961 $MA_SAFE_VELO_STOP_MODE.
- 41 Stop reaction on SE exceeded MD36962 $MA_SAFE_POS_STOP_MODE.
- 42 Standstill speed MD36960 $MA_SAFE_STANDSTILL_VELO_TOL.
- 43 Memory test, stop reaction.
- 44 Actual position + SG[0] MD36931 $MA_SAFE_VELO_LIMIT[0].
- 45 Actual position - SG[0] MD36931 $MA_SAFE_VELO_LIMIT[0].
- 46 Actual position + SG[1] MD36931 $MA_SAFE_VELO_LIMIT[1].
- 47 Actual position - SG[1] MD36931 $MA_SAFE_VELO_LIMIT[1].
- 48 Actual position + SG[2] MD36931 $MA_SAFE_VELO_LIMIT[2].
- 49 Actual position - SG[2] MD36931 $MA_SAFE_VELO_LIMIT[2].
- 50 Actual position + SG[3] MD36931 $MA_SAFE_VELO_LIMIT[3].
- 51 Actual position - SG[3] MD36931 $MA_SAFE_VELO_LIMIT[3].
- 52 Standstill position + tolerance MD36930 $MA_SAFE_STANDSTILL_TOL.
- 53 Standstill position - tolerance MD36930 $MA_SAFE_STANDSTILL_TOL.
- 54 Actual postion + n_x + tolerance MD36946 $MA_SAFE_VELO_X + MD36942
$MA_SAFE_POS_TOL.
- 55 Actual postion + n_x MD36946 $MA_SAFE_VELO_X.
- 56 Actual postion - n_x MD36946 $MA_SAFE_VELO_X.
- 57 Actual postion - n_x - tolerance MD36946 $MA_SAFE_VELO_X - MD36942
$MA_SAFE_POS_TOL
- 58 Active external standstill request.
- 59 SG override factor 1 MD36932 $MA_SAFE_VELO_OVR_FACTOR[0].
- 60 SG override factor 2 MD36932 $MA_SAFE_VELO_OVR_FACTOR[1].
- 61 SG override factor 3 MD36932 $MA_SAFE_VELO_OVR_FACTOR[2].
- 62 SG override factor 4 MD36932 $MA_SAFE_VELO_OVR_FACTOR[3].
- 63 SG override factor 5 MD36932 $MA_SAFE_VELO_OVR_FACTOR[4].
- 64 SG override factor 6 MD36932 $MA_SAFE_VELO_OVR_FACTOR[5].
- 65 SG override factor 7 MD36932 $MA_SAFE_VELO_OVR_FACTOR[6].
- 66 SG override factor 8 MD36932 $MA_SAFE_VELO_OVR_FACTOR[7].
- 67 SG override factor 9 MD36932 $MA_SAFE_VELO_OVR_FACTOR[8].
- 68 SG override factor 10 MD36932 $MA_SAFE_VELO_OVR_FACTOR[9].
- 69 SG override factor 11 MD36932 $MA_SAFE_VELO_OVR_FACTOR[10].
- 70 SG override factor 12 MD36932 $MA_SAFE_VELO_OVR_FACTOR[11].
- 71 SG override factor 13 MD36932 $MA_SAFE_VELO_OVR_FACTOR[12].
- 72 SG override factor 14 MD36932 $MA_SAFE_VELO_OVR_FACTOR[13].
- 73 SG override factor 15 MD36932 $MA_SAFE_VELO_OVR_FACTOR[14].
- 74 SG override factor 16 MD36932 $MA_SAFE_VELO_OVR_FACTOR[15].
- 75 Velocity limit n_x MD36946 $MA_SAFE_VELO_X.
- 76 Stop reaction SG1 MD36963 $MA_SAFE_VELO_STOP_REACTION[0].
- 77 Stop reaction SG2 MD36963 $MA_SAFE_VELO_STOP_REACTION[1].
- 78 Stop reaction SG3 MD36963 $MA_SAFE_VELO_STOP_REACTION[2].
- 79 Stop reaction SG4 MD36963 $MA_SAFE_VELO_STOP_REACTION[3].
- 80 Modulo value for safe cam MD36905 $MA_SAFE_MODULO_RANGE.
- 81 Actual velocity tolerance MD36948 $MA_SAFE_STOP_VELO_TOL.
- 82 SG override factor SGE 0...15 = active SGE position. -1 = SG override inactive (neither SG2 nor
SG4 active, or function is not selected in MD36901 $MA_SAFE_FUNCTION_ENABLE).
- 83 Acceptance test time different MD36958 $MA_SAFE_ACCEPTANCE_TST_TIMEOUT.
- 84 Delay time Stop F -> Stop B MD36955 $MA_SAFE_STOP_SWITCH_TIME_F.
- 85 Delay time pulse disable bus failure MD10089 $MN_SAFE_PULSE_DIS_TIME_BUSFAIL.
- 86 Single encoder system MD36914 $MA_SAFE_SINGLE_ENC.
- 87 Encoder assignment MD36912 $MA_SAFE_ENC_INPUT_NR.
- 88 Cam enable MD36903 $MA_SAFE_CAM_ENABLE.
- 89 Encoder limit frequency MD36926 $MA_SAFE_ENC_FREQ_LIMIT.
- 90 Cam SGA outside MD36940 $MA_SAFE_CAM_TOL different
- 91 Cam position MD36936 $MA_SAFE_CAM_POS_PLUS[4] + MD36940 $MA_SAFE_CAM_TOL.
- 92 Cam position MD36936 $MA_SAFE_CAM_POS_PLUS[4].
- 93 Cam position MD36937 $MA_SAFE_CAM_POS_MINUS[4] + MD36940 $MA_SAFE_CAM_TOL.
- 94 Cam position MD36937 $MA_SAFE_CAM_POS_MINUS[4].
© Siemens AG, 2009. All Rights Reserved
SINUMERIK 840D sl, 840Di sl, SINAMICS, Diagnostics Manual (DAsl), 03/2009
Overview of Alarms
NCK alarms
2-405