Siemens Sinumerik 840D sl Diagnostic Manual page 509

03/2009
Remedy: Causes of error:
1. Error code = A
2. Error code = B
61429 [Channel %1: ] Block %2: Measuring axis (rotary axis 1 or 2) not in basic
or intended position -> Error code: %4
Parameters: %1 = Channel number
%2 = Block number, label channel number
Definitions: The alarm can be triggered by the following measuring cycles: CYCLE996
Remedy: Causes of error:
1. Error code = A
2. Error code = B
3. Error code = C -> Rotary axis 2 not in intended position on 2nd or 3rd measurement in compar-
ison to 1st measurement, see parameters _OVR[63 to 65]
4. Error code = D -> Rotary axis 1 not in intended position on 2nd or 3rd measurement in compar-
ison to 1st measurement, see parameters _OVR[60 to 62]
61430 [Channel %1: ] Block %2: Kinematic vectors not computed -> Error code:
%4
Parameters: %1 = Channel number
%2 = Block number, label channel number
Definitions: The alarm can be triggered by the following measuring cycles: CYCLE996
Remedy: Causes of error:
1. Error code = A
lengths must not be equal to zero
of not being able to form a triangle, check => check PM1...3.)
2. Error code = B
is equal to zero 0.
3. Error code = C
is equal to 0.
4. Error code = D
is equal to 0.
5. Error code = E
6. Error code = F
61440 [Channel %1: ] Block %2: Position of cutting edge cannot be determined
Parameters: %1 = Channel number
%2 = Block number, label channel number
Definitions: The alarm can be triggered by the following measuring cycle: CYCLE982
Remedy: A turning tool with a cutting edge position between 1 and 8 must be used as the tool type.
Check the entered cutting edge position with reference to the basic position of the tool carrier.
61441 [Channel %1: ] Block %2: Position of cutting edge is not in the machining
plane.
Parameters: %1 = Channel number
%2 = Block number, label channel number
Definitions: The alarm can be triggered by the following measuring cycle: CYCLE982
Remedy: The position of the cutting edge of the turning tool (cutting tip) is no longer in the machining plane
(interpolation plane), this can be caused, for example, by a tool carrier with orientation capability. Cor-
rect the tool carrier position.
61442 [Channel %1: ] Block %2: Tool carrier not parallel to the geometry axes
Parameters: %1 = Channel number
%2 = Block number, label channel number
Definitions: The alarm can be triggered by the following measuring cycle: CYCLE982
© Siemens AG, 2009. All Rights Reserved
SINUMERIK 840D sl, 840Di sl, SINAMICS, Diagnostics Manual (DAsl), 03/2009
-> Number of log files in the current directory > 99
-> Log files too long. Rename or delete log files,
check MD11420 $MN_LEN_PROTOCOL_FILE.
-> Rotary axis 1 not in basic position on 1st measurement
-> Rotary axis 2 not in basic position on 1st measurement
-> Plausibility of the input points PM1, PM2, PM3 not fulfilled, resulting side
(Notice: even in the case of side lengths not equal to zero, there is a risk
-> Enclosed angle at PM1 between the spread vectors PM1PM2 and PM1PM3
Starting points do not form a triangle.
-> Enclosed angle at PM2 between the spread vectors PM2PM1 and PM2PM3
Starting points do not form a triangle.
-> Enclosed angle at PM3 between the spread vectors PM3PM1 and PM3PM2
Starting points do not form a triangle.
-> Normalizing interpolation point: Invalid axis name defined for computation
-> Normalizing interpolation point: Invalid plane defined for computation
Overview of Alarms
NCK alarms
2-509