Kenwood NEXEDGE NX-200 Function Reference page 120

6 SOUND
6.1 Tones that Sound When a User Operates the Transceiver or When the Transceiver Status Is Changed
Function
Stop Tone
Password Authorization
Tone
Queue Tone
Free System Ringback
Mode Tone
Ringer Tone
Priority-channel Tone
Scan Stop Tone
Individual Call Tone
Fleet Call Tone
Group Call Tone
Search Mode Tone
Out of Range Tone
Call Request Tone
Zone 1 Select Tone
(NX-200S/ NX-300S only)
Zone 2 Select Tone
(NX-200S/ NX-300S only)
Zone 3 Select Tone
(NX-200S/ NX-300S only)
Zone 4 Select Tone
(NX-200S/ NX-300S only)
OTAP Reactivation
Pre-alert Tone
FUNC (K)/Ver 4.00
This tone sounds from the transceiver if "End Stop" is configured for Rollover/ End Stop.
This tone sounds from the transceiver if a user attempts to decrease the zone, channel, or GID number
while the zone, channel, or GID having the lowest number is selected. Also, this tone sounds from the
transceiver if a user attempts to increase the zone, channel, or GID number while the zone, channel, or
GID having the highest number is selected. (Refer to
This tone sounds from the transceiver if the entered password matches the password preconfigured for
the transceiver.
This tone sounds from the transceiver while the transceiver is searching with the Auto Telephone in an
LTR Trunking system for an available RIC repeater to be connected to. This tone sounds from the
transceiver every 1 sec until an available RIC repeater to be connected to is found or Auto Telephone is
terminated if the transceiver cannot find an available RIC repeater within 60 sec.
This tone sounds from the transceiver when the transceiver enters Free System Ringback Mode in an
LTR Trunking system.
This tone sounds from the transceiver when a repeater is temporarily available on Free System
Ringback Mode in an LTR Trunking system.
This tone sounds from the transceiver when the scan is paused on a Priority-channel.
Pressing the Home CH/GID or Direct CH/GID key during the scan causes the transceiver to migrate to
the Home CH/GID or Direct CH/GID. This tone sounds from the transceiver at 30-sec intervals while the
scan pauses.
This tone sounds from the transceiver when the transceiver initiates an Individual Call of FleetSync.
This tone sounds from the transceiver when the transceiver initiates an Individual Call of FleetSync.
This tone sounds from the transceiver when the transceiver initiates an Individual Call of FleetSync.
This tone sounds from the transceiver when the transceiver initiates Forced Search in an NXDN
Trunking system.
This tone sounds at intervals of 30 sec from the transceiver when the transceiver is in the searching
state, even if 10 sec elapse after the transceiver starts searching for a control channel in an NXDN
Trunking system.
NXDN Trunking system:
This tone sounds from the transceiver when the transceiver initiates an Individual Call or Group Call by
pressing the PTT switch.
NXDN Conventional system:
This tone sounds from the transceiver when the transceiver initiates an Individual Call (Individual Call
Acknowledge Request) by pressing the PTT switch.
For NX-200S/ NX-300S, this tone sounds from the transceiver if Zone 1 is selected.
For NX-200S/ NX-300S, this tone sounds from the transceiver if Zone 2 is selected.
For NX-200S/ NX-300S, this tone sounds from the transceiver if Zone 3 is selected.
For NX-200S/ NX-300S, this tone sounds from the transceiver if Zone 4 is selected.
This tone sounds at 500-millisecond intervals from the transceiver while the transceiver is in OTAP
Reactivation Mode.
Description
Rollover/ End Stop on page
CONTENTS
28.)
INDEX 86