Kenwood NEXEDGE NX-200 Function Reference page 550

APPENDIX
Available Functions for the PF Keys
Function Name
SDM (FleetSync/NXDN)
Selcall (FleetSync)
Selcall + SDM (FleetSync)
Selcall + Status (FleetSync)
Send the GPS Data
Site Down
Site Down (Continuous)
Site Lock
Site Select
Site Up
FUNC (K)/Ver 4.00
The transceiver enters Short Message Mode. In Short Message Mode, a
Short Message can be sent by a user directly entering a Short Message.
For an Analog Conventional system, a Short Message is sent to a Target
Fleet/ ID.
For NXDN Conventional system and NXDN Trunking system, a Short
Message is sent to a Base ID. (Refer to
Short Message (Short Data Call) on page
Receiving a Short Message (Short Data Call) on page
Note
For NX-200S/ NX-300S, this function cannot be assigned.
Enters Selcall Mode. In Selcall Mode, a call can be initiated by a user
selecting a Fleet/ ID from an ID List or directly entering a Fleet/ ID. (Refer
to 12.4 Making a Selective Call on page
Note
For NX-200S/ NX-300S, this function cannot be assigned.
Enters Selcall Mode. In Selcall Mode, a call can be initiated by a user
selecting a Fleet/ ID registered in the ID List or directly entering a Fleet/
ID. Then, pressing the Menu ([
Selcall Mode allows the transceiver to enter Short Message Mode. In
Short Message Mode, a Short Message can be sent by a user directly
entering a Short Message. (Refer to
Message (Short Data Call) on page
Note
For NX-200S/ NX-300S, this function cannot be assigned.
Enters Selcall Mode. In Selcall Mode, a call can be initiated by a user
selecting a Fleet/ ID from an ID List or directly entering a Fleet/ ID. Then,
pressing the Menu ([ ]) or [*] key while the transceiver is in Selcall
Mode allows the transceiver to enter Status Mode. In Status Mode, a
Status Message can be sent by a user selecting a status configured for
Status List or directly entering a Status number. (Refer to
Selective Call on page 309.)
Note
For NX-200S/ NX-300S, this function cannot be assigned.
Manually sends the received GPS data over-the-air from an optionally
installed GPS receiver unit to the base station via a communication port
of the transceiver.
Decreases the site number in steps of 1. (Refer to
to Be Used (Site Lock/ Site Select) on page
Pressing and holding the Site Down key causes the site number to be
decreased in steps of 1 every 100 ms. (Refer to
Be Used (Site Lock/ Site Select) on page
Toggles the Site Lock between enabled and disabled.
Pressing and holding the Site Lock key causes the transceiver to enter
Site Select Mode, and then the site to be stored can be selected. (Refer
to 9.16 Locking the Site to Be Used (Site Lock/ Site Select) on page
Note
For NX-200S/ NX-300S, this function cannot be assigned.
Increases the site number in steps of 1. (Refer to
Be Used (Site Lock/ Site Select) on page
Description
8.10 Sending and Receiving a
163, 12.7 Sending and
336.)
309.)
]) or [*] key while the transceiver is in
12.7 Sending and Receiving a Short
336.)
12.4 Making a
9.16 Locking the Site
236.)
9.16 Locking the Site to
236.)
9.16 Locking the Site to
236.)
Available System
ALL
Analog Conventional System
LTR Trunking System
Analog Conventional System
LTR Trunking System
Analog Conventional System
LTR Trunking System
ALL
NXDN Trunking System
NXDN Trunking System
NXDN Trunking System
236.)
NXDN Trunking System
NXDN Trunking System
CONTENTS INDEX
*1
516