Kenwood NEXEDGE NX-200 Function Reference page 23

CONTENTS
9.8 Making a Group Call with the Link to a
Traffic Channel Retained
(Message Trunked (Enhanced)) ................ 225
Initiating a Group Call
(Message Trunked (Enhanced)).................... 225
Receiving a Group Call
(Message Trunked (Enhanced)).................... 227
9.9 Making an Informative Group Call
(Broadcast Group Call) .............................. 228
Initiating a Broadcast Call.............................. 228
Receiving a Broadcast Group Call ................ 229
9.10 Common Functions for Data
Communications ........................................ 230
Number of Retries ......................................... 230
Transmit Busy Wait Time .............................. 230
Maximum ACK Wait Time ............................. 231
Received Message Display Type
(Message Display Type)................................ 231
9.11 Sending and Receiving a Status Message
(Status Call) ............................................... 232
9.12 Sending and Receiving a Short Message
(Short Data Call) ........................................ 232
9.13 Sending and Receiving a Long Message
(Long Data Call) ......................................... 233
9.14 Communicating with a Telephone
(Telephone Call)......................................... 233
Initiating a Telephone Call ............................. 233
Receiving a Telephone Call........................... 235
9.15 Using DTMF to Initiate a Selective Call...... 236
9.16 Locking the Site to Be Used
(Site Lock/ Site Select)............................... 236
9.17 Adding a Group ID by Remote Control
(Remote Group Add).................................. 240
Sending the Message Requesting to Change
the Remote Group or Reset the Change of
the Remote Group ......................................... 240
Receiving the Message Requesting to Change
the Remote Group or Reset the Change of
the Remote Group ......................................... 240
Transceiver's Behavior when Using the
Regroup ID .................................................... 243
9.18 Transceiver Behavior in the Case that the
System Fails to Provide the Trunking
Control Service (Failsoft)............................ 244
9.19 Transceiver Behavior in the Case that the
Site Fails to Connect to the Network
(Network Failure)........................................ 245
9.20 Sending GPS Data..................................... 246
Transmission Method of GPS Data ............... 246
The ID of the Target Transceiver
(Base ID) ....................................................... 246
Sending GPS Data on a Channel in an
NXDN Conventional System
(GPS Data Zone-Channel) ............................ 247
Sending GPS Data Preferentially While
Receiving a Group Call
(GPS Report Priority (Over Group Call)) ....... 248
GPS Functions .............................................. 248
FUNC (K)/Ver 4.00
9.21 Receiving GPS Data .................................. 249
Map Header................................................... 249
GPS Position Display .................................... 249
9.22 Disabling the Transceiver Capability by
Remote Control (Stun/ Kill) ........................ 249
9.23 Actions for Other Transceivers................... 250
Monitoring the Situation Around Another
Transceiver by Remote Control
(Remote Monitor)........................................... 250
Checking Whether Another Transceiver is in
Operation (Radio Check)............................... 250
10 ANALOG CONVENTIONAL
SYSTEM ................................................251
10.1 Initiating Voice Communications
(Basic Transmission and Reception) ......... 251
Receiving....................................................... 251
Temporarily Disabling the Squelch
(Squelch Off) ................................................. 251
Adjusting the Reception Sensitivity of the
Transceiver (Squelch Level).......................... 253
Participating in an On-going Voice Call Midway
Through the Call (Late Entry) ........................ 255
Searching Whether the Transceiver Receives
a Call (Scan).................................................. 255
Transmitting................................................... 255
Restricting the Continuous Transmission
Duration (Time-out Timer) ............................. 255
Avoiding Interference with Other
Communications (Busy Channel Lockout
(Analog))........................................................ 257
Preferentially Using a Channel Being Used by
Other Parties (BCL Override) ........................ 258
Communicating Without Using a Repeater
(Talk Around)................................................. 259
10.2 Using the Signaling .................................... 260
Sharing the Same Channel (Frequency)
by Several Groups (QT/DQT)........................ 260
Using the Optional Signaling (Analog)........... 261
Unmuting the Speaker
(Audio Control (Analog))................................ 261
Temporarily Disabling the Signaling
(Monitor) ........................................................ 262
Unmuting the Speaker by Linking with the
Microphone (Off-hook Decode)
(Mobile Only) ................................................. 264
10.3 Changing the Decode/ Encode Combination
of the QT/DQT (OST)................................. 265
Configuring the OST to be Enabled or
Disabled......................................................... 265
Selecting the OST List................................... 266
Using the Keypad to Select the OST Code
(Direct OST) .................................................. 266
OST Status Memory ...................................... 268
Disabling the QT/DQT Decode/ Encode
(Tone Off) ...................................................... 268
OST Table ..................................................... 269
10.4 Using 2-tone to Initiate a Selective Call ..... 269
Selecting and Sending the 2-tone Code from
a List .............................................................. 269
INDEX xxi