12.10 Receiving Gps Data; Map Header - Kenwood NEXEDGE NX-200 Function Reference

12 FleetSync

12.10 Receiving GPS Data

12.10 Receiving GPS Data
The base station receiving GPS data from the transceiver of a mobile station can send the GPS data to the PC as serial
commands. If a PC installed with a mapping application is connected to the communication port of the base station
transceiver, the location information of mobile station transceivers appears on a map on the PC display. This function is
convenient for dispatch control or a traffic control system.
Also, if a mobile station transceiver connecting to a GPS receiver unit receives location information (GPS data) from a
GPS satellite, the current location information of the own transceiver can be displayed on the LCD.
Note
• If the optional VGS-1 unit is installed in the transceiver, the GPS data acquired from the GPS satellite can be stored at certain intervals
in the VGS-1 Unit. (Refer to
• For a transceiver receiving GPS data, "Data+GPS Data Output" must be assigned to the communication port connected to a PC
installed with the mapping application. (Refer to

Map Header

Whether to send data to the Mapping software when the base station transceiver receives the GPS data from a base
station transceiver can be configured using KPG-111D/ DN.
Following are the types of data that can be sent to the Mapping Software.
Data
Upon receipt of the GPS data, the transceiver at the base station extracts the $GPGGA data in the NMEA-183
$GPGGA (NMEA)
format from the received GPS data and sends the extracted data from the communication port.
Upon receipt of the GPS data, the transceiver at the base station extracts the $GPGLL data in the NMEA-183
$GPGLL (NMEA)
format from the received GPS data and sends the extracted data from the communication port.
Upon receipt of the GPS data, the transceiver at the base station extracts the $GPRMC data in the NMEA-183
$GPRMC (NMEA)
format from the received GPS data and sends the extracted data from the communication port.
Upon receipt of the GPS data, the transceiver at the base station creates the $PKLDS data which is the
Kenwood proprietary sentence from the received GPS data and sends the created data from the communication
$PKLDS (KW)
port.
The $PKLDS data contains the $GPRMC data in the NMEA-0183 format, Fleet, ID, and the status information.
Upon receipt of the GPS data, the transceiver at the base station creates the $PKLID data which is the Kenwood
proprietary sentence from the received GPS data and sends the created data from the communication port.
The transceiver at the base station extracts only Fleet, ID, and the status information from the received GPS
$PKLID (KW) data and sends the extracted data from the communication port. This sentence is recommended to be used
along with $GPGGA (NMEA), $GPGLL (NMEA) or $GPRMC (NMEA). For example, if $GPGGA (NMEA) and
$PKLID are used simultaneously, the transceiver at the base station sends from the communication port the
$GPGGA data in addition to the Fleet, ID, and the status information extracted from the GPS data.
Upon receipt of the GPS data, the transceiver at the base station creates the $PKLSH data which is the
Kenwood proprietary sentence from the received GPS data and sends the created data from the communication
$PKLSH (KW) port.
The $PKLSH data contains the $GPGLL data in the NMEA-0183 format, Fleet, and ID.
In order to send GPS data in Emergency Mode or by pressing the PTT switch, this sentence is used.
Configuration using KPG-111D/ DN
Configuring the Map Header (
FUNC (K)/Ver 4.00
Storing the GPS Data (GPS Data Storage) on page
Available Functions for COM Port on page
Table 12-20 Map Header
See FPRG 8.11.4 GPS Tab)
473.)
524.)
Description
CONTENTS INDEX 348