Table of Contents
Advertisement
Service Conditions (cont'd)
7.
When using this feature via the FCCS network, PAGING ACCESS [P-1], PAGING TRANSFER [P-10]
and RADIO PAGING [R-16] are provided to the paging station and the paged station in FCCS nodes.
8.
When using this feature via the FCCS network, when PAGING ACCESS [P-1]/PAGING TRANSFER [P-
10]/RADIO PAGING [R-16] service is set to a station in the remote node or the PAGING ACCESS [P-
1]/PAGING TRANSFER [P-10]/RADIO PAGING [R-16] call is answered from the remote node via
FCCS link:
a.) the logical route number should be applied to each physical route that is provided the service.
b.) the restriction of route-to-route connection between FCCS nodes should be released.
9.
When using this feature via the FCCS network, the same paging route cannot be used by another station
while the paged station does not answer the page activated using the route. However, the paging activation
is automatically cleared when the call is not answered within a predetermined time.
10.
When using this feature via the FCCS network, a user can page one station at a time.
Interactions
1.
PAGING TRANSFER (MEET-ME PAGING) and PAGING ACCESS [P-1] can be provided
simultaneously in the same system. Separate access codes for each service is required. A MEET-ME
PAGING answer code is required for each MEET-ME PAGING zone.
2.
Paging is limited to stations and Attendant Consoles. Other parties (CO and TIE trunk calls) must have the
Attendant Console or user perform the paging operation.
3.
The Attendant cannot dial the MEET-ME PAGING answer codes.
4.
BUSY VERIFICATION [B-3], EXECUTIVE OVERRIDE [E-1]: These features will be denied to Paging
routes assigned in CDN 6:TCL as data "8", Page with ringback tone.
5.
PAGING TRANSFER OPERATION: Station A is connected to Party B. Station A momentarily presses
the switch hook or presses the TRANSFER key (if D
(MEET-ME PAGE) route access code. When connected to the page, Station A requests Station C to dial
the MEET-ME PAGE answer code. Station A hangs up. When station C dials the answer code, Party B is
connected to Station C. Station A is removed from the connection.
6.
If Station C does not call the MEET-ME PAGE answer code after 30 seconds, Party B rings back to Station
A. This timer can be changed by ASYD System Data 1 Index 74 b0~b3.
7.
Stations allowed Priority Page, SFI = 57, will barge into the paging route, except when the Attendant
Console is paging.
8.
To answer PAGING TRANSFER while connected to another party, CALL HOLD [C-6] must be used.
THREE-WAY CALLING [T-2] may not be established.
9.
A station must be assigned a Route Restriction Class that allows access to the routes involved in the
PAGING TRANSFER.
Programming
STEP 1:
ASYD - System Data 1, Index 73, Bits 0 & 1:
For MEET-ME PAGE, Non-Delay service, Bit 0 = 1, Bit 1 = 0.
For MEET-ME PAGE, Delay service, Bit 0 = 0, Bit 1 = 1.
For MEET-ME PAGE, Delay service with Call Transfer, Bit 0 = 1, Bit 1 = 1.
System Data 1, Index 73, Bit 3. Are PAGE cancel codes provided for each route? 0/1: Per route/
Common to all routes.
NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
Paging Transfer
term
phone) and then dials the PAGING TRANSFER
P-10
Page 591
Advertisement
Table of Contents
