Table of Contents
Advertisement
Interactions (cont'd)
2.
CONSULTATION HOLD [C-17]: Station A places Party B on CONSULTATION HOLD [C-17] and
calls Station C. If Party B is a trunk, Station C hears DISTINCTIVE RINGING for a trunk call. If Party
B is a station, Station C hears distinctive ringing for a station call.
3.
When Personal Ringer function is set to a station, if an incoming internal call is terminated to the personal
number and the call is transferred by CALL FORWARDING - DON'T ANSWER [C-3], Ringer Pattern
of the transferred station varies depending upon the type of the telephone as shown below:
TYPE OF TRANSFERRED STATION
Programming
STEP 1:
ASYD - System Data 1, Index 72, Bit 6. Is DISTINCTIVE RINGING applied to calls handled via the
Attendant Console? 0/1: No/Yes. Otherwise, these calls will ring as station-to-station calls.
RINGER PATTERN 0 - Normally used for C.O. Calls.
System Data 3, Index 0. Timer Value for Ringer Pattern 0. Normally, data 21Hex (1 sec.-ON, 2 sec.-
OFF) is assigned to this Index.
System Data 3, Index 3, Bit 0. 2-Burst (0.4 sec.-ON, 0.2 sec.-OFF, 0.4 sec.-ON) on the ON Time for
Ringer Pattern 0. 0/1:Not Required/Required.
RINGER PATTERN 1
System Data 3, Index 1. Timer Value for Ringer Pattern 1. Normally, data 42Hex (2 sec.-ON, 4 sec.-
OFF) is assigned to this Index.
System Data 3, Index 3, Bit 1. 2-Burst (0.4 sec.-ON, 0.2 sec.-OFF, 0.4 sec.-ON) on the ON Time for
Ringer Pattern 1. 0/1:Not Required/Required.
RINGER PATTERN 5
System Data 3, Index 7. Timer Value for Ringer Pattern 5.
System Data 3, Index 3, Bit 5. 3-Burst (0.4 sec.-ON, 0.2 sec.-OFF, 0.8 sec.-ON, 0.2 sec.-OFF, 0.4 sec.-
ON) on the ON Time for Ringer Pattern 5. 0/1:Not Required/Required.
System Data 1, Index 417, Bit 0. Recall Ringer Pattern for CALL BACK [C-1], CALL WAITING -
ORIGINATING [C-31], and OUTGOING TRUNK QUEUING [O-2].
0/1:Ringer Pattern 5/Ringer Pattern 1.
STEP 2:
ARTD - To provide a distinctive ring to specific routes, assign data "1" to CDN 12:DR.
STEP 3:
ASFC - Assign a Service Feature Class that allows SFI 48, Burst Ringing, to PA-16LC port station
that will not operate using DISTINCTIVE RINGING. With this feature, the system does not look at
ASYD, System Data 3, Index 3, Bits 0 and 1 to determine how this telephone will ring. Telex, FAX
machines, and OPX stations may require a longer ringing signal. Digital D
feature.
Assign a Service Feature Class that allows SFI 148 to the stations that activates Personal Ringer
function. Personal Ringer function changes Ringing Pattern for Incoming Internal Call according to
the called number as shown below:
Incoming Internal Call terminated to Pilot Number: RINGER PATTERN 1
Incoming Internal Call terminated to Personal Number (ex. My Line): RINGER PATTERN 5
NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
Distinctive Ringing
Analog Telephone
term
D
RINGER PATTERN
1
5
term
s will not respond to this
D-10
Page 285
Advertisement
Table of Contents
