Table of Contents
Advertisement
O-2D
Interactions
1.
Dial pad operation for D
a programmable line/feature key.
2.
OGQ-AUTOMATIC may operate with either same or separate access codes. If the Automatic option is
chosen, service set tone will be sent when encountering an all trunks busy situation. No dial pad operation
will be required.
3.
When testing OGQ, at least one trunk of the trunk group being tested must be engaged in a station-to-trunk
or trunk-to-trunk connection. Use of the MB key only on the trunk circuit card will not allow OGQ to test
and operate properly.
Programming
STEP 1:
ASYD - System Data 1, Index 68, Bit 3. Enables automatic cancel timer, as set in System Data 1,
Index 159. 0/1: -/Enable.
System Data 1, Index 159. OGQ release timer. Standard data of 00H for 30 minutes may be assigned.
(RAM data of 3C [Hex] provides for 30 minutes).
System Data 2, Index 4, Bit 0. Should the access code for CALL BACK and OGQ be the same? 0/1:
No/Yes. Usually assign data "1". Assign on a per-tenant basis.
System Data 2, Index 4, Bit 1. Enable Automatic OGQ? 0/1: No/Yes. Assign on a per-tenant basis.
Automatic operation eliminates the need to access via dial pad.
System Data 2, Index 4, Bit 2. Enable OFF-HOOK OGQ for the Attendant Console? 0/1: No/Yes.
Assign on a per-tenant basis. (See OUTGOING TRUNK QUEUING-ATTENDANT [O-16].)
System Data 1, Index 139, timer for the recall ringing.
STEP 2:
ANPD - Reserve a number level for service feature access and cancel. Assign Connection Indexes, CI
= N, H, B; Normal (N), Hooking (H), and Busy (B) (applicable to any feature assigned to this level).
Assign NND in accordance with a predetermined numbering plan.
STEP 3:
ASPA - If System Data 2, Index 4, Bit 0 is assigned for separate access codes, assign an access code to
OGQ, SRV = SSC (Service Code), SID = 19, and to OGQ cancel, SRV = SSC (Service Code), SID =
20. Assign SID = 19 for a Connection Index of Busy (B) and SID = 20 for a Connection Index of
Normal (N). If the access codes are the same, either the access codes for OGQ or the access codes for
CALL BACK may be assigned.
STEP 4:
ASFC - If access codes are separate, assign a Service Feature Class that allows SFI 1 to stations that
will have OGQ. If access codes are the same, assign an SFC that allows SRI 1, SFI 1 and SFI 2 to the
station.
STEP 5:
ARTD - Routes to be used for OGQ must be flagged in CDN 9:TQ, Trunk Queuing Service. Always
allow queuing to Route 31, the LCR (S) flag route.
STEP 6:
AKYD - For D
[5].
STEP 7:
ADSL - SN=6 (Trunk is Busy) and FKY=5 (Call Back; CB).
This command is used for assigning the function to each soft key.
FCCS Programming
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
STEP 1:
ASYDN - These data must be assigned to the NCN.
Page 558
Outgoing Trunk Queuing - D
term
sets may be exercised. A FLASH BUTTON [F-3D] must be programmed to
term
set the following data to assign CALL BACK Key. Type:Function:CALL BACK
Note 1
term
NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
Advertisement
Table of Contents
