Table of Contents
Advertisement
Programming
STEP 1:
ASYD - System Data 1, Index 16, Bit 3. Enable the 4-digit station number. It is normal to enable all
options regarding length of station numbering. Assign data 1FH.
System Data 1, Index 65. Assign the number of routes in the system.
System Data 1, Index 70, Bit 0. Is Calling Number for a DID incoming to the Attendant in service? 0/
1: No/Yes.
STEP 2:
ARTD - Assign the DIRECT INWARD DIALING route as shown below:
RT:1
3-ISGS
8-RLP
*This can be assigned as data 1, DDD
Note:
STEP 3:
ATRK - Assign the LENs, DID Trunk Route Number, Trunk Number, and Tenant Number.
Assign the LENs and Incoming Register Trunk Route number (903). The LENs must be for levels 0-3
for any 8RST circuit card. (See Interactions.)
STEP 4:
MBTK - Assign the make idle status to the DID and Incoming Register Trunks.
STEP 5:
ANPD - Reserve a number level for station access. Assign for Normal (N) and Hooking (H) service.
Number of Necessary Digits (NND) is usually four, and the Busy Lamp Field is activated.
STEP 6:
ASPA - Assign the access code as assigned in ANPD above. Type of Service, SRV = STN (Station).
Four is the number of digits usually required.
STEP 7:
ARSC - The DID station receiving the call must be assigned a Route Restriction Class (RSC) that will
allow the station to be connected to the incoming DID route. The DID route must be allowed via Route
Restriction Indexes (RRI) 0 & 1.
FCCS Programming
This data setting describes only the additional or replacement commands used to activate FCCS
services. When used as an FCCS feature, these commands replace the non-network commands (for
example, AAED is replaced by AAEDN). Note that the data setting for FCCS service varies depending
on the node.
STEP 1:
ARTDN - Assign the DIRECT INWARD DIALING route as shown below:
RT:1
3-ISGS
8-RLP
STEP 2:
ANPDN - Reserve a number level for station access. Assign for Normal (N) and Hooking (H) service.
Number of Necessary Digits (NND) is usually four, and the Busy Lamp Field is activated.
STEP 3:
ASPAN - Assign the access code as assigned in ANPD above. Type of Service, SRV=TELN. Four is
the number of digits usually required.
STEP 4:
ARSCN - The DID station receiving the call must be assigned a Route Restriction Class (RSC) that
will allow the station to be connected to the incoming DID route. The DID route must be allowed via
Route Restriction Indexes (RRI) 0 & 1.
When using ASYDL or ASYDN to program an FCCS feature, the basic programming of ASYD is required
Note:
in addition to ASYDL or ASYDN.
NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
Direct Inward Dialing (DID)
:7
4-INSG
:3
:2
15-LSG
:8
Note
:7
4-INSG
:3
:2
15-LSG
:8
5-TF
:2
6-TCL
28-ANS
:1
46-CW
5-TF
:2
6-TCL
28-ANS
:1
46-CW
D-8
:5*
7-L/T
:1
:1
:5
7-L/T
:1
:1
Page 281
Advertisement
Table of Contents
